101-4BS Double doors digital display timer blast temperature drying oven

1.Outline：

This product is widely used in industrial and mining enterprises, scientific research institutions,  hospital, medical and other laboratory drying of goods, baking melting, melting and sterilization, curing use.

2.the structural characteristics

1) The shell is made of high quality cold-rolled or cold-rolled steel plate production, the surface coating process, clean and nice.
2)the liner is made of stainless steel or cold-rolled steel plate or embalmed, molding.
3)through the Intermediate steel door with glass viewing window, the situation of the heated items in the working chamber can be observed at anytime.
4)with the double-door design, it’s small occupation space, and easy to use. The high-temperature box door inlaid strips, keep sealing well and prevent heat loss.
5)it’s easy to observe and read the chamber temperature in the digital display.
6)Intelligent PID microprocessor thermostat with a timer, alarm function, and E-type sensor as the temperature measurement control system of the device, the measurement error is small and high precision temperature control.
7)the exhaust valve disposed in the side of chamber, the moisture discharged outside the box heater can be released at any time in the working process.
 

3. principle of operation

After heated by electricity, and fan forced circulation , the air in the working chamber will be heated uniformly with the heat exchange in order to achieve the purpose of drying or baking.

4.Normal operating conditions

1) Power supply voltage: 380v50Hz 

2) Ambient temperature: 5 ~ 40 ℃ 

3) Relative humidity: <85% 

4) No vibration and airflow around the existence of a strong 

5) non-corrosive gases exist.

5.The main technical parameters    

Model : 101-4S

Instrumentation, liner type (S smart meter, BS for stainless steel liner)

Model 101-4BS / 4S 

Supply voltage 380V.50Hz 

Specification 25A fuse 

Temperature range of room temperature + 20 ~ 250 ℃ 

Temperature fluctuation ± 1 ℃ 

Temperature uniformity ± 2.5% 

Heating power 6KW 

Studio Size 800 * 800 * 1000mm 

Spacer bearing 15kg / piece

6.Application method:

1)Open the door, will be required to place objects inside the heated separator, shut the door.
2)Through consistent with this equipment requires power, and will be used by the ground terminal of the power supply socket and reliable grounding;
3)Turn the power switch, power indicator light. Can be selected according to the required heating temperature set. 1. The half-power heating, or heating. 2. The full-power heating, it is recommended to use heated below 100 ℃ to control; above 100 ℃ using a heated 2 full-power heating control, or the need to quickly heat up and then use heated 1 to control the temperature, and reduce energy consumption to conserve electricity.
4)According to the article the temperature needs to be heated, set the desired temperature, temperature control device if the pointer temperature controller on the rotational temperature setting knob (digital display temperature control device may refer to manual).
5)After the work is completed, you can clean off and switch the power.

7.Attention

1) shall not flammable, explosive, corrosive materials or after heating to release flammable, explosive, corrosive, volatile items into the tank is heated.
2) heated items shall not be greater than 85% relative humidity
3) Items needed to dry the area shall not be greater than 70% separators, easy items dry and ventilated.

8.Installation and maintenance

1) Ground (table) should be flat
2) non-flammable around, explosive, corrosive materials and gases
3) from the wall with appropriate 20-30cm
4) a well-ventilated, dust off a small amount of air humidity is greater than 85%
5) keep inside and outside clean, dry
6) The oven should not be stacked above items.

9.Troubleshooting

10.Transportation and storage

Drying of the product stored in -20 ~ + 40 ℃, and a cool environment, do not crash and severe vibration during transportation and prevent rain.

11.Accessories

1) Operating Instructions :1 pcs
2) certificate :1pcs
3) separator :2pcs
4) the temperature controller manual:1 pcs